Safety procedures
in the workshops, battery chargers, welding shops rubber,
First, the design of the workshop
must be all the elements of the workshop
materials, non-flammable§
- take into account the availability of
adequate natural ventilation openings on the area of not less than (sixth)
area of the workshop§
- Jeb availability of natural lighting
the appropriate slots§
- matching all wiring and electrical
installation of the technical assets safe§
- Listed arise from non-combustible to
put the batteries§
- workshop provides an electrical
breaker to disconnect the power cord after the end of daily work, or when
emergency§
Second, while working workshop
proves the charger in a suitable place
away from the workers' movement.§
- keep all the wiring and electrical
installations in proper condition and safe.§
- should never be stored inside the
workshop acids increase the need for daily work.§
- keeps the acid in a glass jar placed
in turn inside the basin of the construction hall tiled with§ sand soft
.§ - The provision of personal protective
equipment for workers, such as protective gloves and other acids.
- workshop to provide fire fighting
devices of the type of carbon dioxide§
.§ - Providing the means for first aid.
restrict workers to prevent smoking.§
compliance with personal protective
equipment necessary for such work (rubber gloves, goggles or eye protector for
the face).§
take into account the implementation of
this process in a site dedicated for this purpose are available where adequate
ventilation and exhaust the right way.§
must open the seals to allow gas escape.§
are provided the appropriate number of
fire extinguishers that are dry powder (powdered) or carbon dioxide at this
location.§
must be taken to ensure adequate and
Reserve when using sulfuric acid during the process of pouring or discharge.§
If there is scattering of the acid wash
immediately and ask for medical assistance.§
You must provide special facilities for
eye wash near the area to be used in case of emergency.§
Safety in welding shops rubber
First, the design of the workshop
must be all the elements of the workshop
materials, non-flammable.§
allocate a separate room from
non-flammable for air compressors so consistent with the requirements of the
most important engineering assessments and to allow vent explosive wave to a
place free and safe in the event of an explosion.§
the provision of natural ventilation
openings so that the workshop area of not less than (sixth) area of the
workshop.§
Match All wiring and electrical
installation of the technical assets safe.§
The workshop provides an electrical
breaker to disconnect the power cord after the end of daily work, or when an
emergency.§
Ensure a continuous basis the validity
of the safety valves, meters, air Alambinat own Dwagt§
Safety procedures in the operations of the paint
(Paint workshops and Deco dyeing cars)
First, the design of the workshop
arise all the elements of the workshop
materials, non-flammable§
must be expanded and auto paint shop to
the biggest truck on a vacuum to be around at least a meter from each side§
The workshop provides fans an eyedropper
to withdraw gases and prefers to use local ventilation near sources of spray
Doco§
the availability of slots must be
natural lighting of the workshop on an area of not less than (sixth) area of
the workshop§
must be the availability of water
resource and sanitation workshop for the exchange of materials resulting§
places should be available to employees
personal hygiene workshop§
Match All wiring and electrical
installation of the technical assets safe§
Tdhud workshop stream breaker to switch
off the power after the end of daily work, or when emergency§
Second, while working workshop
provide workers Emamat appropriate for
the protection of the respiratory system from fumes and gases§
training of workers on the use of
personal protective equipment and properly archive (masks - gloves - aprons ...
etc.).§
the need for primary medical lobe and
the league and the exclusion of ill sensitivity of the skin and chest§
Prohibition of storage of large
quantities of oil cans or paint thinner or increase workshop about the need for
daily work.§
Prohibition of the dumping of
contaminated oils paints rugs workshop§
maintain all wiring and electrical
installations in proper condition and safe§
staff aware of work hazards and ways
Tbesaarham Prevention (CDC)§
tested lifters used the workshop as a
regular patrol by the professionals responsible§
providing the means for preliminary
control of the fire (fire extinguishers) and train staff to use§
provision of first aid and training a
staff to do the first ambulance for the injured§
Smoking is prohibited inside the
workshop and attached a sign that§
care must be clean floors constantly and
make sure they are free from all residues completely§
be careful when mixing paints / solvents
or poured from a container to another, or when you move and clear of any spill
of these materials without delay.§
get rid of the rags or pieces of cotton
and other materials contaminated with solvents, pigments, oils and grease by
placing them in a metal container away from any source of heat or direct
sunlight for fear of self-combustion§
Wear personal protective equipment
required before the start of work and special breathing protectors§
ensure the safety of the workplace
ventilation.§
Use the correct type of spray equipment
and ensure safety and cleanliness periodically§
Close the valve air pressure to the pump
and release the fluid pressure in the system before attempting to remove the
spray nozzle and the farthest from your body.§
deal with hoses carefully and keep them
safe.§
your hands clean of paint using
detergents and allows the§ use of thinner
for this purpose.
No comments:
Post a Comment
Welcome: Your comments very important for our progress