safety precautions in the storage of materials

Procedures and safety precautions in the storage of materials

Storage areas usually contain strategic reserves of the facilities of raw materials or product and other equipment and machinery, which is estimated funds of money, so it was necessary to secure the stores of the danger of fire or burglary and theft to preserve what they contain, and the process is based fire insurance to prevent erupted and full readiness to confront him in case it occurs because of the fires posed by heavy losses of materials stored combustible. And even in the case of non-usability of combustion it harm her exposure to the smoke or the rise in temperature as a result of a fire to other materials and flammable nearby, as well as damage may occur as a result of water used in fire fighting operations. There are three considerations when followers due to the process of securing the most important stores separate storage locations for manufacturing sites, and avoid the existence of any sources of ignition sites of storage and take measures to limit the spread of fire when it occurs storage sites.

Safety procedures in handling and lifting operations

Safety procedures in handling and lifting operations

 Make sure that there is no risk on the ground, especially slippery materials such as oils and fats as well as the earth is flat down the body to be lifted.§
 the values ​​of the size and body weight to be lifted and ask for help from others in the event of your inability to raise the body alone.§
 Be careful not to corner the fingers of the hand or the bottom of heavy exposure to the acute injury of the parties or the fall of the body on the feet.§
 to protect against back injuries that may result from erroneous methods of lifting materials be sure to follow the correct way to lift materials as follows:§

safety precautions in dealing with electricity& elevators

procedures and safety precautions in  dealing with electricity

Have on workers in the workshops of the institution comply with procedures and safety precautions for the prevention and protection from power supply and in particular consider the following:

 not to touch any of the electrical conductors before hand to make sure that its activity using electrical measuring devices allocated to it.§

 not to resort to the introduction of the parties to the bare electrical wiring in the sockets and the use of  Pistons  triangular.§

 Ensure that all electrical connections are covered with insulating material and protected by a secure way.§

Safety procedures in dealing with materials and devices

 Safety procedures in dealing with materials and devices:

1 - safety procedures in dealing with tires

 Dealing with the tires is limited to trained personnel.§

 adhere to wear personal protective equipment necessary to perform the work.§

 tire is inflated in steel cages allocated to it.§

 taking into account the safety standard blower tires and a commitment to use in such operations.§

 maintain the integrity of the air compressor and other equipment associated with this work.§

 conduct periodic inspection for the future of air in the compressor (Alkimberasr) once a year at least.§

 Safety procedures in the workshops, battery chargers, welding shops rubber,

First, the design of the workshop

 must be all the elements of the workshop materials, non-flammable§

 - take into account the availability of adequate natural ventilation openings on the area of ​​not less than (sixth) area of ​​the workshop§

 - Jeb availability of natural lighting the appropriate slots§

 - matching all wiring and electrical installation of the technical assets safe§

 - Listed arise from non-combustible to put the batteries§

 - workshop provides an electrical breaker to disconnect the power cord after the end of daily work, or when emergency§

Safety measures in car workshops

Safety measures in car workshops

This includes personal safety and the safety of personnel, vehicles, equipment and facilities and the safety of the environment.
Risks Porsche cars:

Vehicle / car as a source of risk:

- toxic gases (carbon monoxide)
- a potentially explosive gas (fuel vapors, gas battery)
- harmful gases (fuel vapors, acids)
- Plankton air (filings brakes, diesel soot smoke)
- toxic liquids (fuel, brake fluid)
- cocktails acids (acid battery)
-flammable liquids (fuel, brake fluid)
- hot liquids (liquid cooling)
 -slippery liquids (oils and fluids poured on the ground)
- parts and materials under pressure (springs, pools pressure, compressed air)
 -heavy parts (parts of the car, the car on the lift)
- rotating parts (belts, fan)
- hot parts (brakes, radiator,)
-sharp parts (iron sheets car)
- electric current (with HV, Blacks, Blacks cable)
- moving vehicles
- loud noise (engine)

Safety requirements in mechanical workshops

Safety requirements and safety in 
:mechanical workshops

:A - General procedures for safety in the workshops

 First, the design of the workshop

 must be all the elements of the establishment of the workshop materials, non-flammable§

 must be poured concrete floor to prevent the drink material and petroleum oils§

 must be safe all electrical connections§

 provide the workshop stream breaker to switch off the power after the end of daily work, or when emergency§

 The workshop provides a resource and an aqueous wash basin and a suitable system for the exchange§